Gallonly

How Fuel Economy Is Tested: The Five Test Cycles

See how window-sticker values are produced: dynamometer tests, the city, highway, high-speed, air conditioning and cold cycles, and who actually runs the tests.

By Gallonly Editorial Team 6 min read

On this page
  1. Key takeaways
  2. Who runs the tests
  3. The five test cycles
  4. From five tests to one label number
  5. How electric vehicles and plug-in hybrids are tested
  6. Why the method changed over time
  7. What the tests are and are not

Fuel economy ratings come from laboratory tests: a vehicle is driven on a dynamometer, which works like a treadmill for cars, through standardized driving schedules. Results from five kinds of test are used to build the city and highway values on the window sticker. Automakers supply most of the data, and regulators audit it and re-test a share of vehicles themselves.

Key takeaways

  • The dynamometer lets every vehicle follow the same speed trace, so ratings are comparable across models.
  • Five tests cover city driving, highway driving, high speed with hard acceleration, hot weather with air conditioning, and cold weather.
  • Manufacturers provide the data used for labels. Regulators confirm approximately 15% of all test results in their own laboratory.
  • Since the 2008 model year, the method includes faster speeds, air conditioning and cold weather, which lowered estimates for all vehicles.

Who runs the tests

Regulators define the test methods and the calculation of label values, but it is the manufacturers that are responsible for providing the fuel economy data used for labeling, testing at their own facilities. That data is audited, and some vehicles are re-tested independently. For electric vehicles and plug-in hybrids, confirmatory testing is performed on all new light-duty models of those types.

Manufacturers test one representative vehicle for each combination of loaded vehicle weight class, transmission class and basic engine, rather than every trim or option package. That is one reason two trims of the same model can share a rating.

The five test cycles

The rating method uses five cycles, each following a published driving schedule:

TestWhat it representsAverage speedTop speedDistance
CityStop-and-go urban driving, engine started cold21.2 mph56 mph11 miles
HighwayRural and Interstate driving, engine warm48.3 mph60 mph10.3 miles
High speed (US06)City and highway driving at higher speeds with harder acceleration and braking48.4 mph80 mph8 miles
Air conditioning (SC03)Hot conditions, with the air conditioner set to cool21.2 mph54.8 mph3.6 miles
Cold (city test at 20 degrees F)Cold-start driving in cold weather, with heat and defrost settings21.2 mph56 mph11 miles

The SC03 test accounts for air conditioning under hot outside conditions, with a 95 degrees F sun load. The cold test is the city schedule run in a laboratory at 20 degrees F. The city, highway and high-speed tests run without heating, ventilation or air conditioning in operation.

From five tests to one label number

For many vehicles the full set of tests is run and combined. The procedures also allow a derived approach, in which city and highway test results are adjusted with factors based on data from vehicles that were fully tested, so not every model needs every cycle in the lab. The label’s city and highway values are then combined into the headline number using a 55% city and 45% highway weighting; see city vs highway MPG and the combined rating.

How electric vehicles and plug-in hybrids are tested

Electric vehicles are driven in repeated laboratory cycles until the battery is depleted, then recharged to measure the energy used. The recharge energy includes charger losses. Range and energy use are then adjusted for real-world factors. The label can use a factor of 0.7 applied to the test results, and most EVs use that approach or an equivalent. Label range combines city and highway at the same 55% and 45% weights.

Plug-in hybrids are tested in two operating conditions: charge-depleting, starting with a full battery, and charge-sustaining, starting with an empty one. How plug-in hybrids are rated explains how the two results are combined.

Why the method changed over time

The method was updated in 2008 to account for faster speeds and acceleration, air conditioner use and colder outside temperatures, and these changes lowered fuel economy estimates for all vehicles. For model year 2017, some of the calculations used to estimate fuel economy were updated based on actual vehicle data from the 2011 to 2016 model years. Most vehicles were not affected, some estimates fell by 1 mpg, and a small number were 2 mpg lower. See why model year ratings change.

What the tests are and are not

Laboratory testing is designed for repeatable comparison. It is not a prediction of your own mileage, a point covered in real-world MPG vs the window sticker. To see how Gallonly turns label values into dollars, read the methodology.

This guide is general education, not purchase, financial or legal advice. It explains how ratings and costs are defined and does not rank or recommend vehicles.

Use the numbers on real cars

Work out what a specific car costs to fuel, compare gas with electric, or browse the window-sticker ratings.

Related guides